Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX · Furnace parts

Furnace flame sensor repair in Schertz

Burners light, run for a few seconds, then shut off, and the furnace tries again? That's the classic sign of a dirty or failing flame sensor, one of the most common and affordable furnace repairs.

What the flame sensor does

The flame sensor is a thin metal rod, usually with a white ceramic base, positioned in the path of one burner's flame. It's a safety device. After the gas valve opens, the control board needs proof that the gas actually lit. If it doesn't get that proof within a few seconds, it shuts the gas off so unburned gas can't build up.

The sensor works by flame rectification: the flame conducts a tiny electrical current, measured in millionths of an amp (microamps), from the rod to the burner. A clean sensor in a good flame produces a strong signal. A coated sensor produces a weak one, and the board shuts the burners down even though there's a flame.

Signs of a dirty or failing flame sensor

  • Burners light, then go out after 3–10 seconds
  • The furnace repeats that cycle several times, then locks out
  • A blinking code on the board pointing to "flame sense" or "failed ignition"
  • Heat works sometimes and fails other times, especially on cold mornings
  • A visible dull, black or white coating on the rod

Why flame sensors get dirty

Combustion leaves a thin oxide and carbon film on the rod over time. Several things speed it up:

  • Months of idle dust. In Schertz, furnaces sit unused from spring to fall, and dust settles in the burner area.
  • Drywall and construction dust after remodeling, which is very common in newer subdivisions
  • Household chemicals stored near the furnace (cleaners, paint, pool chemicals). Their vapors can coat the sensor.
  • Poor combustion from wrong gas pressure or dirty burners
  • Weak grounding, which can mimic a dirty sensor even when the rod is clean

Cleaning vs replacing

Most of the time, the sensor just needs cleaning. We remove it, clean the rod with a fine abrasive pad, check the ceramic for cracks, and measure the microamp signal after reinstalling it. We replace it when:

  • The ceramic insulator is cracked
  • The rod is pitted, bent or corroded
  • The signal stays weak even after cleaning
  • It keeps getting dirty within weeks, along with fixing the underlying cause

Cleaning it yourself? Turn off power at the furnace switch and close the gas valve first. Remove the single screw holding the sensor, clean only the metal rod with a fine abrasive pad (not coarse sandpaper), don't touch the ceramic, and reinstall it firmly. If the furnace still shuts off afterward, or you're not comfortable working in the burner compartment, call a technician.

When it's not the flame sensor

If cleaning doesn't help, the problem may be a weak flame from low gas pressure, poor grounding, a reversed polarity on the 120V supply, or a failing control board. If the burners never light at all, look at the igniter instead. Furnace still shutting off? Read furnace keeps shutting off.

Flame sensor repair cost

Typical flame sensor costs in SchertzParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Flame sensor cleaning $90 – $175 Often done during a repair or tune-up
Flame sensor replacement $120 – $250 Universal or OEM sensor, installed
Included in a tune-up $80 – $200 Cleaning and testing are part of maintenance
FAQ

Flame Sensor Repair FAQs

Don't see your question? Call (210) 898-9282.

How often should a flame sensor be cleaned?

Once a year during a furnace tune-up is usually enough. If it needs cleaning every few weeks, something is contaminating it, and we'll find the cause.

How long does a flame sensor last?

Often 5–10 years or more with regular cleaning. Replacement is needed when the ceramic cracks or the rod corrodes.

Is a dirty flame sensor dangerous?

No. It's actually a safety feature doing its job. The furnace shuts off the gas because it can't confirm a flame. It's inconvenient, not dangerous.

Can I use sandpaper to clean a flame sensor?

Use a fine abrasive pad or fine steel wool. Coarse sandpaper can leave scratches and grit that make the sensor foul faster.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate