Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX · Furnace parts

Furnace igniter replacement in Schertz

Hear the furnace start up, click, and then nothing? A cracked hot surface igniter is the most common reason a gas furnace won't light, especially on the first cold day of the season.

What the igniter does

Most gas furnaces built in the last 25 years use a hot surface igniter (HSI) instead of a standing pilot light. It's a small ceramic element that glows red-hot, above 1,800°F, for a few seconds. When the gas valve opens, the gas touches the glowing element and the burners light.

There are two common types:

  • Silicon carbide: the older, flat, lattice-shaped style. Very brittle, and easily cracked by vibration or a fingertip's skin oil.
  • Silicon nitride: the newer, rounder style. More durable and longer lasting, and a common upgrade when the original fails.

Some older furnaces use a standing pilot with a thermocouple, or a spark-ignited intermittent pilot. Those fail differently. See pilot light won't stay lit.

Signs of a bad furnace igniter

  • The inducer motor starts, you hear clicks, but the burners never light
  • The furnace tries to light three or four times, then locks out (often with a blinking code)
  • Looking through the sight glass, there's no orange glow during start-up
  • Ignition works sometimes and not others, a sign of a hairline crack
  • You can see a visible crack or white spot on the igniter element

Why igniters fail on the first cold day in Schertz

An igniter heats up and cools down every heating cycle, and that thermal stress slowly weakens the ceramic. In Schertz, the furnace then sits for months in a hot garage or attic. When the first cold front arrives and the furnace fires up, a weakened igniter cracks. That's why igniter calls spike in November and December.

Other causes that shorten igniter life:

  • Touching the element during cleaning or installation. Oils create hot spots that crack it.
  • High voltage from an electrical supply above 120V, or a failing control board
  • Short cycling, which means more heat-up cycles per day (often from an oversized furnace or clogged filter)
  • Dust and drywall debris after a renovation

How we diagnose and replace it

  1. Watch the sequence: confirm the inducer runs and the pressure switch closes, so the igniter is actually being called.
  2. Check voltage at the igniter during the ignition step. No voltage points to the control board, not the igniter.
  3. Test resistance and inspect the element for cracks.
  4. Replace with a matched igniter: correct voltage, shape and mounting, handled without touching the element.
  5. Test multiple cycles and check that the flame sensor and burners are clean while we're in there.

Why not DIY? Igniters cost little, but they crack if handled, sit beside the gas burners and connect to 120V. A wrong-spec igniter can burn out quickly. If the igniter isn't the real cause, a new one won't fix the furnace.

Igniter or something else?

If the igniter glows but the burners still don't light, the problem is the gas valve or gas supply. If the burners light and then go out after a few seconds, that's the flame sensor. If the igniter never gets power, look at the pressure switch or control board.

Furnace igniter replacement cost

Typical igniter costs in SchertzParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Silicon carbide igniter, installed $150 – $300 Matches many older furnaces
Silicon nitride igniter, installed $200 – $450 More durable upgrade
OEM brand-specific igniter $250 – $450 Some models require original parts
Diagnostic (if billed separately) $80 – $200 Often credited toward the repair
FAQ

Igniter Replacement FAQs

Don't see your question? Call (210) 898-9282.

How long does a furnace igniter last?

Typically 3–7 years, depending on type and how often the furnace cycles. Silicon nitride igniters usually last longer than silicon carbide.

Can a furnace run with a cracked igniter?

Sometimes, for a while. A hairline crack can still glow intermittently. It will fail completely, usually on a cold night, so replace it once it's diagnosed.

Why does my new igniter keep burning out?

Repeated failures point to an underlying cause: high supply voltage, a failing control board, short cycling, or the wrong igniter for the furnace. We check those before replacing it again.

Is the igniter the same as the flame sensor?

No. The igniter lights the gas. The flame sensor confirms a flame exists. They sit near each other and are often confused, but they fail with different symptoms.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate