Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX

Gas furnace repair in Schertz, TX

Furnace clicks but won't light? Lights, then shuts off? We repair natural gas and propane furnaces of every brand, and every visit includes a carbon monoxide safety check.

A gas furnace lights in a precise sequence, and when any step fails, the control board shuts everything down for safety. Repair means finding exactly which step failed.

How a gas furnace starts (and where it fails)

  1. Thermostat calls for heat. Failure point: a dead thermostat, bad wiring or a blown low-voltage fuse.
  2. The inducer motor starts to clear the heat exchanger and flue. Failure point: a seized or noisy inducer motor.
  3. The pressure switch confirms the draft. Failure point: a clogged condensate trap, blocked vent or failed switch (pressure switch repair).
  4. The igniter glows red-hot. Failure point: a cracked hot surface igniter, the most common no-heat cause.
  5. The gas valve opens and the burners light. Failure point: a failed gas valve or gas supply issue.
  6. The flame sensor proves the flame. Failure point: a dirty flame sensor shuts the gas off after a few seconds.
  7. The blower starts and pushes warm air through your ducts. Failure point: a failed capacitor or blower motor.

Most furnaces flash a code on the control board's LED that points to the failed step. Our furnace blinking light codes post explains how to read it. A code narrows the search, but it still needs to be confirmed with testing.

Common gas furnace problems in Schertz

Cracked igniter on the first cold day

Hot surface igniters are brittle and often fail after sitting all summer. You'll hear the inducer run and click, but no flame.

Lights, then shuts off

The classic dirty flame sensor. The burners light for 3–10 seconds, go out, and the furnace retries.

Pressure switch lockouts

High-efficiency furnaces in attics often have clogged condensate traps, which trip the pressure switch.

Yellow or lazy flames

A healthy flame is mostly blue. Yellow or floating flames can mean dirty burners or poor combustion and need prompt attention.

Gas safety: if you smell rotten eggs (the odorant added to natural gas), leave the home and call 911 or your gas utility from outside. Don't try to relight a furnace or open its burner compartment if you smell gas.

Every gas furnace repair includes a combustion safety check

A gas furnace that heats isn't necessarily safe. On every visit we:

  • Test for carbon monoxide at the furnace and in the living space
  • Inspect the heat exchanger for cracks, rust and soot
  • Check the flue and venting for blockages and proper draft
  • Check gas pressure and look for leaks at the valve and connections
  • Inspect flame color and burner condition

If we find a cracked heat exchanger, we'll show you the evidence. A crack can allow carbon monoxide into your air, and it's often the point where replacement makes more sense than repair.

Propane furnaces on rural lots

Some properties on the edges of Schertz, Cibolo and Marion use propane instead of natural gas. Propane furnaces use the same components but a different gas valve setting and orifices. We service both, and we'll check the regulator and tank supply if the problem points there.

Gas furnace repair cost in Schertz

Typical gas furnace repair costsParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Flame sensor clean or replace $90 – $250 Lights, then shuts off
Hot surface igniter $150 – $450 Clicks, no flame
Pressure switch $150 – $450 Often a clogged trap, not the switch
Inducer motor $450 – $1,500 Humming or whining before ignition
Gas valve $300 – $1,000 Igniter glows, no gas flow
Control board $350 – $900 Varies widely by brand
FAQ

Gas Furnace Repair FAQs

Don't see your question? Call (210) 898-9282.

Why does my gas furnace click but not turn on?

Clicking usually means the control board is trying to start the ignition sequence. The most common causes are a cracked igniter, a pressure switch that won't close, or a gas supply problem. See furnace not turning on for safe checks.

Can I clean my own flame sensor?

Some homeowners do, with the power and gas off, using fine steel wool or an abrasive pad. If you're not comfortable working inside the burner compartment, call a technician. Our flame sensor guide covers the process and when replacement is needed.

How often should a gas furnace be checked for carbon monoxide?

At least once a year, ideally during a fall tune-up, and any time the furnace is repaired. Every home with a gas furnace should also have working CO alarms near bedrooms and on each level.

Is a yellow flame in my furnace dangerous?

It can be. A mostly yellow, floating or sooty flame indicates incomplete combustion, which can produce carbon monoxide. Turn the furnace off and have it inspected.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate