Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Furnace troubleshooting

Furnace pilot light won't stay lit?

Only older gas furnaces have a standing pilot light, a small flame that burns all the time. If yours keeps going out, the cause is usually a worn thermocouple or a dirty pilot.

Quick answer

The most common cause is a weak or failed thermocouple, the safety device that keeps the gas valve open only while the pilot is lit. A dirty pilot orifice, drafts and low gas pressure are other causes. Relight only by following the instructions on your furnace's label, and call a technician if it won't stay lit.

Do you actually have a pilot light?

Most furnaces installed in the last 25 years don't have a standing pilot. They use a hot surface igniter or an intermittent spark pilot that lights only when heat is needed. If you look through the sight window and see no small blue flame when the furnace is off, you likely have electronic ignition, and this guide doesn't apply. See furnace not turning on instead.

How a standing pilot works

A small flame burns continuously near the burners. Its heat warms a thermocouple, a metal rod that generates a tiny electrical current. That current holds the gas valve's pilot safety open. If the pilot goes out, the thermocouple cools within seconds, and the valve shuts off gas so it can't leak into the home.

Why the pilot won't stay lit

Worn thermocouple

The most common cause. It lights while you hold the button, then goes out when you release it.

Dirty pilot orifice

Dust and soot shrink the flame until it no longer heats the thermocouple properly. A healthy pilot flame is steady and mostly blue.

Drafts

Air movement in a garage or closet can blow out a weak pilot, especially with a loose access panel.

Gas supply or valve

Low gas pressure or a failing gas valve. Check whether other gas appliances work normally.

Relighting a pilot: safety basics

If you smell gas, don't relight anything. Leave the home and call 911 or your gas utility from outside. See furnace smells like gas.

Every furnace with a standing pilot has lighting instructions printed on a label near the gas valve. Follow that label exactly. The general pattern looks like this:

  1. Turn the thermostat down and the gas control knob to OFF.
  2. Wait at least 5 minutes (or as long as the label says) for any gas to clear.
  3. Turn the knob to PILOT, press and hold it, and light the pilot with the built-in igniter button or a long lighter, as directed.
  4. Keep holding for 30–60 seconds so the thermocouple heats up, then release slowly.
  5. Turn the knob to ON and raise the thermostat.

If the pilot goes out as soon as you release the knob, or won't stay lit after a second try, stop. Repeated attempts won't fix a failed thermocouple.

The repair

A technician cleans the pilot assembly, adjusts the flame and tests the thermocouple's output. Thermocouple replacement is an inexpensive repair, often $120–$300. On an older pilot-light furnace, it's also worth asking how much life the furnace has left. Many are now past 25 years old. See repair or replace.

FAQ

Frequently asked questions

Don't see your question? Call (210) 898-9282.

Why does my pilot light go out when I let go of the button?

The thermocouple isn't producing enough current to hold the gas valve open. Usually it's worn or not positioned in the flame, or the pilot flame is too weak.

Is it safe to relight my furnace pilot myself?

Yes, if you follow the furnace's printed instructions exactly and there's no gas smell. If it won't stay lit after one or two tries, call a technician.

Should I replace a furnace that still has a standing pilot?

Not automatically, but standing-pilot furnaces are typically older and less efficient. If it needs a major repair, compare the cost with a new furnace.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate