Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Furnace troubleshooting

Why is my furnace blowing cold air?

Cold air from the vents when the heat is on is one of the most common furnace complaints in Schertz. Here's how to narrow down the cause, starting with the easy fixes.

Quick answer

The most common causes are the thermostat fan set to ON instead of AUTO, a clogged filter causing an overheating shutdown, a dirty flame sensor, or a failed igniter. In heat pump homes, a defrost cycle can blow cool air for a few minutes, which is normal.

Check these first (safe for anyone)

1. Thermostat fan set to ON

If the fan setting is ON, the blower runs constantly, even between heating cycles, pushing room-temperature air that feels cold. Set it to AUTO so the blower runs only while the furnace is heating.

2. The furnace just started

A gas furnace takes 30–90 seconds to heat the heat exchanger before the blower starts. Some systems push a little cool air from the ducts at first. Give it two minutes.

3. Clogged air filter

A dirty filter restricts airflow, the furnace overheats, and the high-limit switch shuts off the burners while the blower keeps running, blowing cool air. Replace the filter and see if steady heat returns. This is especially common during mountain cedar season. See our filter guide.

Causes that usually need a technician

4. Dirty flame sensor

The burners light, then shut off after a few seconds because the sensor can't confirm the flame. The blower may keep running and circulate cooling air. See flame sensor repair.

5. Failed igniter

No ignition means no heat, and on some systems the blower still runs. Listen for the inducer starting and clicking with no "whoosh" of burners. See igniter replacement.

6. Gas supply problem

Check whether other gas appliances (stove, water heater) work. If none do, call your gas utility. If only the furnace fails, the gas valve may have failed.

7. Condensate or pressure switch lockout

High-efficiency furnaces, common in Schertz attics, lock out when the condensate trap or drain clogs. See condensate drain repair.

8. Leaky or disconnected attic ducts

If the furnace runs and the air near the unit is warm but your vents are cool, heated air may be escaping into the attic through a disconnected or crushed duct.

9. Heat pump defrost (or failed heat strips)

Heat pumps periodically run a defrost cycle that can blow cool air for a few minutes. That's normal. If it lasts longer than about 15 minutes, or happens constantly, the backup heat strips may not be working. See em heat vs heat and heat strip repair.

Don't keep restarting it. If the furnace locks out after several tries, repeated resets can cause unburned gas to build up. Call a technician instead.

Quick diagnosis table

What you notice Likely cause
Cold air between cycles, constant fan Thermostat fan on ON
Warm at first, then cold, then repeats Overheating (filter) or flame sensor
Clicking, no burner flame Igniter, gas valve or gas supply
Blinking code, water near the unit Condensate / pressure switch
Heat pump, cool air for a few minutes Normal defrost cycle
FAQ

Frequently asked questions

Don't see your question? Call (210) 898-9282.

Why does my furnace blow cold air at first, then warm?

Usually normal. The blower waits until the heat exchanger is hot, but a little cool air left in the ducts comes out first. If cold air lasts more than a couple of minutes, look at the causes above.

Can a dirty filter really make a furnace blow cold air?

Yes. It restricts airflow until the furnace overheats and the limit switch shuts off the burners. The blower keeps running to cool the furnace, which feels like cold air.

How much does it cost to fix a furnace blowing cold air?

Often $90–$450 for the most common causes (flame sensor, igniter, switch). See the furnace repair cost guide.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate